Steps for automount usb by udev rules.
======================================
--> Go to /etc/udev/rules.d/ directory
--> create a file with .rules extension eg :: vijay.rules etc
--> Copy the below code to your file
ACTION=="add",KERNEL=="sd?[1-9]",KERNELS=="2-1.1",SUBSYSTEM=="block",SUBSYSTEMS=="usb",SYMLINK+="usb1",RUN+="/etc/pd.sh usb1"
ACTION=="remove",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",RUN+="/etc/pdut.sh usb1"
ACTION=="add",KERNEL=="sd?[1-9]",KERNELS=="2-1.2",SUBSYSTEM=="block",SUBSYSTEMS=="usb",SYMLINK+="usb2",RUN+="/etc/pd.sh usb2"
ACTION=="remove",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",RUN+="/etc/pdut.sh usb2"
--> save and exit
--> go to /etc directory
--> create a file with name pd.sh
--> copy the below code to your file
#!/bin/sh
sudo mkdir -p /var/$1
sudo mount /dev/$1 /var/$1
--> Save and exit
--> chmod +x pd.sh
--> create a file with name pdut.sh
--> copy the below code to you file
#!/bin/sh
sudo umount /var/$1
sudo rm -rf /var/$1
--> Save and exit
--> chmod +x pdut.sh
--> Reload the rules with command ::
udevadm control --reload-rules or udevcontrol --reload_rules(old Kernels)
--> From next time if you plug in usb these rules are applied
--> Please make the changes wrt your pc in
KERNELS :: please change this as per the usb slot you want to work on
& KERNEL :: if no partition is present i.e only sdd or sdb etc.... if it has sdd1 or sdb1 you can work normally.
=================================================
If You are not interested in kernels and if you are not stick to one mount point you can use these lines
ACTION=="add",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",SYMLINK+="usb%k",RUN+="/etc/pd.sh usb%k"
ACTION=="remove",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",RUN+="/etc/pdut.sh usb%k"
these two lines are enough which can mount any number of usb devices connected to any slot of the pc. pd.sh & pdut.sh are same
but the drawback is the mountpoint name changes
eg :: if 1st usb is connected and if kernel detects it as sdb1 then symlink usbsdb1 is created and mountpoint is /var/usbsdb1
if 2nd usb is connected and if kernel detects it as sdc1 then symlink usbsdbc1 is created and mountpoint is /var/usbsdc1 etc....
VJ
======================================
--> Go to /etc/udev/rules.d/ directory
--> create a file with .rules extension eg :: vijay.rules etc
--> Copy the below code to your file
ACTION=="add",KERNEL=="sd?[1-9]",KERNELS=="2-1.1",SUBSYSTEM=="block",SUBSYSTEMS=="usb",SYMLINK+="usb1",RUN+="/etc/pd.sh usb1"
ACTION=="remove",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",RUN+="/etc/pdut.sh usb1"
ACTION=="add",KERNEL=="sd?[1-9]",KERNELS=="2-1.2",SUBSYSTEM=="block",SUBSYSTEMS=="usb",SYMLINK+="usb2",RUN+="/etc/pd.sh usb2"
ACTION=="remove",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",RUN+="/etc/pdut.sh usb2"
--> save and exit
--> go to /etc directory
--> create a file with name pd.sh
--> copy the below code to your file
#!/bin/sh
sudo mkdir -p /var/$1
sudo mount /dev/$1 /var/$1
--> Save and exit
--> chmod +x pd.sh
--> create a file with name pdut.sh
--> copy the below code to you file
#!/bin/sh
sudo umount /var/$1
sudo rm -rf /var/$1
--> Save and exit
--> chmod +x pdut.sh
--> Reload the rules with command ::
udevadm control --reload-rules or udevcontrol --reload_rules(old Kernels)
--> From next time if you plug in usb these rules are applied
--> Please make the changes wrt your pc in
KERNELS :: please change this as per the usb slot you want to work on
& KERNEL :: if no partition is present i.e only sdd or sdb etc.... if it has sdd1 or sdb1 you can work normally.
=================================================
If You are not interested in kernels and if you are not stick to one mount point you can use these lines
ACTION=="add",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",SYMLINK+="usb%k",RUN+="/etc/pd.sh usb%k"
ACTION=="remove",KERNEL=="sd?[1-9]",SUBSYSTEM=="block",SUBSYSTEMS=="usb",RUN+="/etc/pdut.sh usb%k"
these two lines are enough which can mount any number of usb devices connected to any slot of the pc. pd.sh & pdut.sh are same
but the drawback is the mountpoint name changes
eg :: if 1st usb is connected and if kernel detects it as sdb1 then symlink usbsdb1 is created and mountpoint is /var/usbsdb1
if 2nd usb is connected and if kernel detects it as sdc1 then symlink usbsdbc1 is created and mountpoint is /var/usbsdc1 etc....
VJ